| STATOR INPUT VOLTAGE RATING IN VOLTS | 90.0 NOMINAL |
| STATOR INPUT CURRENT RATING | 13.0 MILLIAMPERES NOMINAL |
| STATOR INPUT ELECTRICAL POWER RATING | 210.0 MILLIWATTS NOMINAL |
| TERMINAL TYPE AND QUANTITY | 5 SCREW |
| BODY STYLE | STANDARD ROUND B |
| FREQUENCY IN HERTZ | 60.0 NOMINAL |
| BODY SIZE | 15 |
| ZSO RESISTANCE IN OHMS | 6000.00 MINIMUM AND |
| 7500.00 MAXIMUM |
| ZRS RESISTANCE IN OHMS | 1300.00 MINIMUM AND |
| 1650.00 MAXIMUM |
| ZSO IMPEDANCE MAGNITUDE IN OHMS | 78.00 MINIMUM AND |
| 82.00 MAXIMUM |
| ZRS IMPEDANCE MAGNITUDE IN OHMS | 13.00 MINIMUM AND |
| 18.00 MAXIMUM |
| TRANSFORMATION RATIO | 0.735 ROTOR TO STATOR NOMINAL |
| PHASE SHIFT ANGLE IN DEG | 9.000 INPUT TO OUTPUT NOMINAL |
| MAXIMUM TEMP RISE | 10.0 DEG CELSIUS |
| MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | 45.00 OUTPUT |
| MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 65.00 |
| ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -6.0 TO 6.0 |
| ACTUATOR FRICTION TORQUE AT MINUS 55 DEG CELSIUS | 0.05 INCH-OUNCES MAXIMUM |
| ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | 0.05 INCH-OUNCES MAXIMUM |
| SHOULDER DIAMETER | 1.3115 INCHES MINIMUM AND |
| 1.3120 INCHES MAXIMUM |
| PILOT DIAMETER | 0.8745 INCHES MINIMUM AND |
| 0.8750 INCHES MAXIMUM |
| OVERALL LENGTH | 3.0430 INCHES MINIMUM AND |
| 3.0830 INCHES MAXIMUM |
| FLANGE DIAMETER | 1.4320 INCHES MINIMUM AND |
| 1.4370 INCHES MAXIMUM |
| FLANGE THICKNESS | 0.0930 INCHES NOMINAL |
| UNDERCUT WIDTH | 0.0780 INCHES NOMINAL |
| PILOT LENGTH | 0.0400 INCHES NOMINAL |
| SHOULDER LENGTH | 0.1320 INCHES NOMINAL |
| MOUNTING SURFACE TO TERMINAL END DISTANCE | 2.3910 INCHES MAXIMUM |
| ALIGNMENT HOLE DEPTH | 0.1250 INCHES NOMINAL |
| ALIGNMENT HOLE BOLT CIRCLE DIAMETER | 1.0970 INCHES MINIMUM AND |
| 1.1030 INCHES MAXIMUM |
| SHAFT TYPE | ROUND, SLOTTED SINGLE SHAFT |
| SHAFT DIAMETER | 0.1867 INCHES MINIMUM AND |
| 0.1872 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT LENGTH | 0.5450 INCHES MINIMUM AND |
| 0.5650 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT SLOT DEPTH | 0.0250 INCHES NOMINAL SINGLE SHAFT |
| SHAFT SLOT WIDTH | 0.0200 INCHES NOMINAL SINGLE SHAFT |
| TERMINAL LOCATION | REAR |
| BODY MATERIAL | STEEL, STAINLESS |
| TEST DATA DOCUMENT | 81349-MIL-S-20708 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| FRAGILITY FACTOR | MODERATELY RUGGED |
| SPECIFICATION/STANDARD DATA | 81349-MIL-S-20708/21 GOVERNMENT SPECIFICATION |