| STATOR INPUT VOLTAGE RATING IN VOLTS | 115.0 NOMINAL |
| STATOR INPUT CURRENT RATING | 75.0 MILLIAMPERES NOMINAL |
| STATOR INPUT ELECTRICAL POWER RATING | 1.6 WATTS NOMINAL |
| FREQUENCY IN HERTZ | 60.0 NOMINAL |
| TERMINAL TYPE AND QUANTITY | 5 SCREW |
| BODY SIZE | 23 |
| BODY MATERIAL | STEEL CORROSION RESISTING |
| ZRO RESISTANCE IN OHMS | 236.00 NOMINAL |
| PLUS J ZRO REACTANCE IN OHMS | 1590.00 NOMINAL |
| ZSO RESISTANCE IN OHMS | 217.00 NOMINAL |
| PLUS J ZSO REACTANCE IN OHMS | 796.00 NOMINAL |
| ZRS RESISTANCE IN OHMS | 485.00 NOMINAL |
| PLUS J ZRS REACTANCE IN OHMS | 167.00 NOMINAL |
| ZSO-90 RESISTANCE IN OHMS | 206.00 NOMINAL |
| PLUS J ZSO-90 REACTANCE IN OHMS | 271.00 NOMINAL |
| TRANSFORMATION RATIO | 0.783 ROTOR TO STATOR NOMINAL |
| MAXIMUM TEMP RISE | 45.0 DEG CELSIUS |
| MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | 75.00 OUTPUT |
| MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 100.00 |
| ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -8.0 TO 8.0 |
| ACTUATOR FRICTION TORQUE AT MINUS 55 DEG CELSIUS | 0.50 INCH-OUNCES MAXIMUM |
| ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | 0.20 INCH-OUNCES MAXIMUM |
| BODY STYLE | STANDARD ROUND D |
| SHOULDER DIAMETER | 1.9850 INCHES MINIMUM AND |
| 1.9900 INCHES MAXIMUM |
| PILOT DIAMETER | 0.5900 INCHES MINIMUM AND |
| 0.6000 INCHES MAXIMUM |
| SECOND SHOULDER DIAMETER | 1.9985 INCHES MINIMUM AND |
| 1.9995 INCHES MAXIMUM |
| SECOND SHOULDER LENGTH | 0.1680 INCHES MINIMUM AND |
| 0.1700 INCHES MAXIMUM |
| OVERALL LENGTH | 4.2940 INCHES MAXIMUM |
| FLANGE DIAMETER | 2.2490 INCHES MINIMUM AND |
| 2.2500 INCHES MAXIMUM |
| FLANGE THICKNESS | 0.2480 INCHES MINIMUM AND |
| 0.2500 INCHES MAXIMUM |
| BODY DIAMETER | 1.9850 INCHES MINIMUM AND |
| 1.9900 INCHES MAXIMUM |
| PILOT LENGTH | 0.0360 INCHES MINIMUM AND |
| 0.0460 INCHES MAXIMUM |
| SHOULDER LENGTH | 0.2500 INCHES NOMINAL |
| AFT OF FIRST FLANGE DIAMETER | 1.9985 INCHES MINIMUM AND |
| 1.9995 INCHES MAXIMUM |
| MOUNTING SURFACE TO TERMINAL END DISTANCE | 3.4450 INCHES MAXIMUM |
| ALIGNMENT HOLE DEPTH | 0.1250 INCHES NOMINAL |
| ALIGNMENT HOLE BOLT CIRCLE DIAMETER | 1.6420 INCHES NOMINAL |
| ALIGNMENT HOLE QUANTITY | 3 |
| SHAFT TYPE | ROUND, THREADED SINGLE SHAFT |
| SHAFT DIAMETER | 0.2402 INCHES MINIMUM AND |
| 0.2405 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT LENGTH | 0.6930 INCHES MINIMUM AND |
| 0.7190 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT THREAD LENGTH | 0.3100 INCHES MINIMUM AND |
| 0.3300 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT THREAD SERIES DESIGNATOR | UNF SINGLE SHAFT |
| SHAFT NOMINAL THREAD SIZE | 0.2500 INCHES SINGLE SHAFT |
| SHAFT THREAD CLASS | 2A SINGLE SHAFT |
| SHAFT THREAD DIRECTION | RIGHT-HAND SINGLE SHAFT |
| TERMINAL LOCATION | REAR |
| SPECIAL FEATURES | SLOTTED KEYWAY FULL LENGTH OF SHAFT |
| TEST DATA DOCUMENT | 81349-MIL-S-20708 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| SPECIFICATION/STANDARD DATA | 81349-MIL-S-20708/94 GOVERNMENT SPECIFICATION |
| FRAGILITY FACTOR | MODERATELY RUGGED |
| SPEC/STD CONTROLLING DATA | |
| MANUFACTURERS CODE | 81349 |
| NON-DEFINITIVE GOVERNMENT SPEC/STD REFERENCE | MILS20708 |