| ALIGNMENT HOLE BOLT CIRCLE DIAMETER | 0.8120 INCHES NOMINAL |
| ALIGNMENT HOLE DEPTH | 0.1250 INCHES MINIMUM |
| ALIGNMENT HOLE QUANTITY | 4 |
| BODY MATERIAL | STEEL, CORROSION RESISTING |
| BODY SIZE | 11 |
| BODY STYLE | STANDARD ROUND C |
| FLANGE DIAMETER | 1.0620 INCHES MAXIMUM |
| FLANGE THICKNESS | 0.0930 INCHES NOMINAL |
| FRAGILITY FACTOR | MODERATELY RUGGED |
| FREQUENCY IN HERTZ | 400.0 NOMINAL |
| III SCHEMATIC DIAGRAM DESIGNATOR | 1 Y-ROTOR, 1 STATOR |
| PILOT DIAMETER | 0.6250 INCHES MAXIMUM |
| PHASE SHIFT ANGLE IN DEG | 6.000 INPUT TO OUTPUT MAXIMUM |
| PILOT LENGTH | 0.0620 INCHES NOMINAL |
| PROPRIETARY CHARACTERISTICS | PACS |
| MAXIMUM TEMP RISE | 25.0 DEG CELSIUS |
| MOUNTING SURFACE TO TERMINAL END DISTANCE | 1.7990 INCHES MAXIMUM |
| NONDEFINITIVE SPEC/STD DATA | 11TR4C TYPE |
| OVERALL LENGTH | 2.3760 INCHES MAXIMUM |
| RECEIVER ERROR ANGULAR RANGE IN MINUTES | -60.0/+60.0 |
| ROTOR INPUT CURRENT RATING | 60.0 MILLIAMPERES MAXIMUM |
| ROTOR INPUT ELECTRICAL POWER RATING | 1.0 WATTS MAXIMUM |
| ROTOR INPUT VOLTAGE RATING IN VOLTS | 115.0 NOMINAL |
| SHAFT END PLAY DETERMINING WEIGHT | 16.0 OUNCES |
| SHAFT END PLAY | 0.0025 INCHES NOMINAL |
| SHAFT DIAMETER | 0.1872 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT LENGTH | 0.5000 INCHES NOMINAL SINGLE SHAFT |
| SHAFT MAXIMUM RADIAL PLAY | 0.0006 INCHES |
| SHAFT MAXIMUM RUNOUT | 0.0008 INCHES |
| SHAFT NOMINAL THREAD SIZE | 0.190 INCHES SINGLE SHAFT |
| SHAFT RADIAL PLAY DETERMINING WEIGHT | 8.0 OUNCES |
| SHAFT RADIAL PLAY TEST POINT | 0.125 INCHES MAXIMUM |
| SHAFT THREAD CLASS | 2B SINGLE SHAFT |
| SHAFT THREAD DIRECTION | RIGHT-HAND SINGLE SHAFT |
| SHAFT THREAD LENGTH | 0.2550 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT THREAD SERIES DESIGNATOR | UNC SINGLE SHAFT |
| SHAFT TYPE | SPLINE W/THREADS SINGLE SHAFT |
| SHOULDER DIAMETER | 1.0000 INCHES MAXIMUM |
| SHOULDER LENGTH | 0.0620 INCHES NOMINAL |
| SPECIFICATION/STANDARD DATA | 81349-MIL-S-20708/3 GOVERNMENT SPECIFICATION |
| SPLINE TOOTH DIAMETRAL PITCH | 120 SINGLE SHAFT |
| SPLINE TOOTH QUANTITY | 21 SINGLE SHAFT |
| ZSS IMPEDANCE ANGLE IN DEG | 22.00 MINIMUM AND 28.00 MAXIMUM |
| ZSS IMPEDANCE MAGNITUDE IN OHMS | 180.00 MINIMUM AND 250.00 MAXIMUM |
| TERMINAL LOCATION | REAR |
| TERMINAL TYPE AND QUANTITY | 5 SCREW |
| TEST DATA DOCUMENT | 81349-MIL-S-20708 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| TORQUE GRADIENT PER ANGULAR DEG | 0.008 INCH-OUNCES MINIMUM |
| TRANSFORMATION RATIO | 0.783 STATOR TO ROTOR NOMINAL |
| UNDERCUT DIAMETER | 0.9750 INCHES NOMINAL |
| UNDERCUT WIDTH | 0.0620 INCHES NOMINAL |