| STATOR INPUT VOLTAGE RATING IN VOLTS | 115.0 NOMINAL |
| STATOR INPUT CURRENT RATING | 40.0 MILLIAMPERES MAXIMUM |
| STATOR INPUT ELECTRICAL POWER RATING | 950.0 MILLIWATTS NOMINAL |
| TERMINAL TYPE AND QUANTITY | 5 SCREW |
| BODY STYLE | STANDARD ROUND C |
| FREQUENCY IN HERTZ | 60.0 NOMINAL |
| BODY SIZE | 18 |
| ZRO IMPEDANCE MAGNITUDE IN OHMS | 2875.00 MINIMUM AND |
| 3375.00 MAXIMUM |
| ZRO IMPEDANCE ANGLE IN DEG | 76.00 MINIMUM AND |
| 80.00 MAXIMUM |
| ZSS IMPEDANCE MAGNITUDE IN OHMS | 660.00 MINIMUM AND |
| 810.00 MAXIMUM |
| ZSS IMPEDANCE ANGLE IN DEG | 9.00 MINIMUM AND |
| 13.00 MAXIMUM |
| TRANSFORMATION RATIO | 0.783 ROTOR TO STATOR NOMINAL |
| PHASE SHIFT ANGLE IN DEG | 11.000 INPUT TO OUTPUT NOMINAL |
| MAXIMUM TEMP RISE | 25.0 DEG CELSIUS |
| MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | 30.00 OUTPUT |
| MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 85.00 |
| ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -8.0 TO 8.0 |
| TORQUE GRADIENT PER ANGULAR DEG | 0.100 INCH-OUNCES MAXIMUM |
| SHOULDER DIAMETER | 1.5615 INCHES MINIMUM AND |
| 1.5620 INCHES MAXIMUM |
| PILOT DIAMETER | 0.9370 INCHES MINIMUM AND |
| 0.9375 INCHES MAXIMUM |
| OVERALL LENGTH | 3.0600 INCHES NOMINAL |
| FLANGE DIAMETER | 1.7450 INCHES MINIMUM AND |
| 1.7500 INCHES MAXIMUM |
| FLANGE THICKNESS | 0.0930 INCHES NOMINAL |
| UNDERCUT DIAMETER | 1.6250 INCHES NOMINAL |
| UNDERCUT WIDTH | 0.0780 INCHES NOMINAL |
| PILOT LENGTH | 0.0400 INCHES NOMINAL |
| SHOULDER LENGTH | 0.1320 INCHES NOMINAL |
| MOUNTING SURFACE TO TERMINAL END DISTANCE | 2.5200 INCHES NOMINAL |
| ALIGNMENT HOLE DEPTH | 0.1250 INCHES MINIMUM |
| ALIGNMENT HOLE BOLT CIRCLE DIAMETER | 1.2500 INCHES NOMINAL |
| ALIGNMENT HOLE QUANTITY | 4 |
| SHAFT TYPE | SPLINE W/THREADS SINGLE SHAFT |
| SHAFT DIAMETER | 0.1870 INCHES MINIMUM AND |
| 0.1872 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT LENGTH | 0.5400 INCHES NOMINAL SINGLE SHAFT |
| SHAFT THREAD LENGTH | 0.2000 INCHES NOMINAL SINGLE SHAFT |
| SPLINE TOOTH QUANTITY | 21 SINGLE SHAFT |
| SPLINE TOOTH DIAMETRAL PITCH | 120 SINGLE SHAFT |
| SHAFT THREAD SERIES DESIGNATOR | UNF SINGLE SHAFT |
| SHAFT NOMINAL THREAD SIZE | 0.190 INCHES SINGLE SHAFT |
| SHAFT THREAD CLASS | 2A SINGLE SHAFT |
| SHAFT THREAD DIRECTION | RIGHT-HAND SINGLE SHAFT |
| TERMINAL LOCATION | REAR |
| BODY MATERIAL | STEEL, STAINLESS |
| TEST DATA DOCUMENT | 81349-MIL-S-20708 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| FRAGILITY FACTOR | MODERATELY RUGGED |
| SPECIFICATION/STANDARD DATA | 81349-MIL-S-20708/33 GOVERNMENT SPECIFICATION |